跳至主要内容

NAFCO | Why radiators must be installed with radiator valves

NAFCO | Why radiators must be installed with radiator valves
Time:2017-12-08 From: NAFCO- Brass Valves China and Brass Fittings Manufacturers China
In the radiator self-heating system, temperature control valves have a very important position, the role of obvious and cannot be missing, if the system is not installed on the gas stove can only rely on the outlet temperature and start and stop the furnace to adjust the heating heat. This does not reach the purpose of comfortable heating, but also a waste of resources, with the home from the original intention of heating a far cry.

Radiator Valves China
China Radiator valves usded for radiators
Then, thermostatic valves how to adjust the role of room temperature? The working principle of the temperature control valve is to control the temperature of the outlet of the equipment by controlling the hot water inlet flow of the heat exchanger so as to adjust the flow rate by changing the valve opening degree when the load changes to eliminate the influence caused by the load fluctuation. The temperature is restored to the set value. The use of temperature control valve users can control the sub-room, select the heating, thus ensuring a constant room temperature, to avoid the heating system hydraulic imbalance and single-tube system uneven upper and lower room temperature problems, and through the role of thermostat control can improve the indoor The comfort of the thermal environment, that is, users can arbitrarily adjust the temperature to meet the diverse needs of the heat.

With the temperature control brass valves like brass radiator valves, brass ball valves, brass check valves can also be adjusted to the best room temperature, such as the long-term uninhabited rooms and kitchen, bathroom and other rooms, the temperature can be set at 8 ℃, the room heating system and the water system can be antifreeze protection; People often sleep bedroom temperature set at 16-22 ℃, sleep at night set at 16 ℃, because people sleep covered quilt at night, the room temperature should not be too high; for office workers, it is recommended to work at home after the shutdown cannot Otherwise, it will take some time to open again, and no money will be saved. For families with young children and elderly people, some rooms need to be set at about 24 ℃, which is the temperature at which they feel comfortable.

In addition to the role of sub-room heating, the temperature control valve also has a distinct energy saving, control the advantages of heating costs. Different from centralized heating, self-heating users need to consider every winter to protect the system and the water is not frozen, because no heating control by the user themselves, and the entire system from the heat source to the cooling terminal all at home, if the house in winter do not live without heating the room, the heating system of the home and the water system will be the risk of pipe cracking, the loss will not be underestimated. In this case, the user can entrust a friend or property to run the system together. The temperature control valve can be set at about 8 °C, which saves money and protects the system.

Radiators self-heating due to sub-room regulation, ease of control temperature, loved by many users, choose to install more and more users. Remind users, in this set of heating system essential valve, must choose to install.
Ningbo Acro Fluid Control Co., Ltd. (NAFCO) is a professional brass valve manufacturers in China for floor heating manifolds, such as brass ball valves ChinaBrass radiator valvesbrass gate valvesbrass angle valves, brass check valves, brass float valves, radiator valves Chinathermostatic radiator valvesbrass fittings China.
In case of futher questions, please feel free to contact NAFCO at www.acrofluid.com, or send emails to support@acrofluid.com.

评论

此博客中的热门博文

NAFCO | Brass Gate Valve Installation

NAFCO | Brass Gate Valve Installation From: NAFCO | China Brass Valves Manufacturer 1. The installation of the gate valve must be carried out by qualified operators. The deviation of the different axial directions of the two ends of the pipeline must not be too large, otherwise excessive pipeline installation stress will be generated, resulting in failure and damage. The thread precision and effective length strictly enforce the ISO228-1 relevant standards.    When installing the screw, the hex or octagonal part of the same side of the thread should be clamped. The hexagonal or octagonal part of the other end of the valve should not be wrenched to avoid deformation of the valve. It must be made of Teflon tape or thread sealant seal.     2. To install the tightening valve, you must use the corresponding torque wrench or pipe wrench, and screw in the effective thread length. Do not excessively cause the inner end surface to be pressed, causing the s...

NAFCO | 5 Negative Changes of China Brass Valve Industry in 2017

1, Sales decline, weak growth In the era of overcapacity, plumbing valve industry oversupply, the valve industry innovation, change lag, in the growth encountered bottlenecks and ceilings, if the business no new growth point, the major brand sales decline is a common phenomenon. 2, Price war The market demand for brass valves is red uced, in order to seize the market, each brand competition bargain, businesses profit are limited. The market shuffle will be inevitable.  China brass valve manufacturers  for  brass ball valves ,  brass gate valves ,  brass check valves , brass angle valves,  brass radiator valves ,  brass fittings  will face difficult time. 3, Brass Valve Industry shuffle Brass valve brand competition will become increasingly fierce in 2018, China brass valve suppliers without core competitiveness and service will be squeezed in the market. In the case of raw material prices and cost increase, non-competitive brass valve factories w...

NAFCO | Definition and Structure of Brass Gate Valves

NAFCO | Definition and Structure of Brass Gate Valves Time:2018-08-02 From: NAFCO | China Brass Gate Valves Manufacturer Brass gate valves are one of the most commonly used plumbing valves for household application, just little smaller than brass ball valves. Brass gate valve is  metal-metal sealed valve and are currently widely used in water supply systems.    Today we're going to explain what is a brass gate valve, what's the structure of brass gate valves:     1. Definition and of Brass Gate Valves   Brass gate valves, also called brass disc valves, are valves in which the closing valve disc moves in the vertical direction along the centerline of the passage, used to turn the media on or off.   The brass gate valve is a control unit that moves the gate plate along the axis of the channel in the vertical direction and shuts off the medium flow control unit through the handwheel rotation drive. The utility model h...